Harman Pellet Stove Igniter Not Working – Let’s Discover Why

Harman pellet stove igniter not working is the common complaint of users who may panic when their significant investment starts to give them shocks by not working well.

However, the reasons behind the non-working of the stove igniter are not very big and are even resolvable, which requires a little bit of attention and maintenance.

The article below will highlight all the possible and common problems that could happen to the Harman pellet stove igniter, which include; inadequate voltage supply, blown a fuse, clogged igniter element, breakdown of ignition coil, and defective igniter.

All the problems discussed below have an overview of their solutions to assist the reader.

Harman Pellet Stove Igniter Not Working

Users often get worried about the Harman pellet stove igniter not working, and some potential customers who have heard about any such issues want to know about the problems before buying the stove.

Well, the problems are not so big and are very common, which could have happened to any other stove igniter as well. Please read the article till the end to get a clearer picture of these problems with their respective solutions.

Harman Pellet Stove Igniter Problems With Their Potential Solutions

Below are some common problems that could happen with the ignitor, which lets the ignitor stop working correctly. Though, all the problems have some potential solutions as well.

Inadequate Voltage Supply

The voltage supply is the main element which enables the working of the ignitor; at times, there comes an issue that the voltage supply does not come in an adequate quantity which hinders the flow of the circuit in the ignitor. Hence, when the supply is proper and sufficient, no such issues come to the notice.

Whenever the Harman pellet stove ignitor stops working, the user must check the supply of voltage to see if it’s enough or not.

Below is how to check the accurate and required voltage supply.

Solution

• The first step is to have a voltmeter, which will eventually measure the voltage supply
• Now check the lowest possible voltage rate by placing the red and black terminals on the edge of the ignitor wire to see what is the lowest voltage value coming
• The required voltage value must be between 115 to 120 volts per cycle on

Now, at this point, the situation will get more apparent; if the voltage value falls between 115 to 120 and the ignitor is still not working, then it is so evident that now is the time to replace the ignitor. Moreover, the issue could be due to a defective fuse, defective circuit board or due to defective coil.

Blown Fuse

After the voltage check, the situation becomes more straightforward and complicated simultaneously. As it is definite that the voltage supply is correct, but now is the time to check the working of the fuse.

Fuses could have burned, which may have resulted in the non-working. This could have happened due to the ignitor getting overheated, or circuit wires may have short-circuited, which could also result in the defective fuse.

Let’s find out how to check the defective fuse and how to solve the issue.

Solution

• First, check the condition of the fuse. Indicates a defect, then do replace it immediately
• If the condition is ok, then do check whether the fuse is working correctly or not
• Make sure to check all the wires of the ignitor as well; tightening of wires sometimes becomes the savior

However, if everything seems to be okay with the fuse, the issue must now lie with the circuit board, which also needs a detailed checkup, but some professional technicians must do that as it requires checking the electric wires in depth.

Clogged Igniter Element

A clogged Igniter also becomes the reason for non-working as continuous heat or dirt can accumulate in the stove, which can result in obstacles and blockages.

That is why the stove requires regular cleaning sessions; below is the overview of how the Harman pellet stove igniter can be made clean.

Solution

• Cooling down the stove is mandatory, so unplug it and let the stove get relaxed for a while
• Afterwards, open the firebox, which needs to be cleaned. Take a brush and take all the dust and debris away from the firebox
• Take a damp cloth and wipe out all of the stubborn dust marks and ashes

After proper and deep cleaning, close the firebox and turn on the stove to check if it’s working correctly.

Breakdown Of Igniter Coil

The coil is placed inside the igniter, which is responsible for creating heat inside the igniter that helps to ignite the wood pellets.

Whenever the coil inside the igniter breaks, the level of heat and redness becomes less, and this indicates the breakdown of the coil.

Solution

• The solution here is simple and straight, replace the coil immediately with the new one

This task must be done with extra care. If the user does not understand the replacement procedure, then it’s better to contact a specialist or professional to carry out this replacement procedure.

Defective Igniter

Sometimes, the igniter becomes useless and needs replacement rather than looking for any other issue.

Replacing the igniter is not much of a difficult task, so one can do this on their own at home without contacting any expert help. Below is the way how to replace the ignitor at home easily.

Solution

• Please turn off the stove and let it cool down first before starting any working
• Afterwards, remove the back of the stove and look for the wires that are attached to the plug; unplug them all
• Pliers are required to remove the old igniter from the plate and for placing the new igniter
• Now, after placing the igniter correctly, place the cover plate back and place the wires also back into the plug
• Lastly, place the back of the stove again in its original place, and the procedure is done

Conclusion

The issue of the Harman pellet stove igniter not working correctly has been discussed in detail. A conclusion can be drawn that whenever the stove stops working, it could be due to multiple reasons, including inadequate voltage supply, defective Igniter, clogged igniter, blown fuse and defective coil.