Hey folks! Have you ever experienced your Harman Pellet stove status light blinking 5 times? The 5 blinks mean no ignition or the stove will not burst into flames in 36 minutes. 

One possibility of blinking the status light 5 times in your Harman stove can be a lot of ash filled into the igniter where the pallets are settled to catch fire.

These pellets need to be cleaned from time to time in a heating season for better results and high maintenance, as it will surely enhance the life of your stove. 

But, the situation can get worse if ashes and pellets build up in your Harman stove, as it can reduce the quality of your stove by damaging the heating pieces of equipment just because you did not take care of your pellet stove maintenance by cleaning it on time.

Not taking care of your Harman stove can also lead it to lose the ability to control the heating temperature, airflow, and the power to catch the flames. That is when the status light can blink 5 times. Therefore, your Harman pellet stove should be cleaned and inspected at least once a year. 

The question is when and why this blinking happens and what to do later to fix this blinking status light problem.

What Happens When Your Harman Pellet Stove Status Light Blinking 5 Times? 

First of all, you have to inspect the problem. Within reach possibilities that you can look over can be either the pallet are not being appropriately combusted in the stove, or the pellet hopper/container is getting stuck, which can happen either through failure or insulated by ash. 

We can put this mess in a more understandable way to understand the “5 times blinking status light in Harman pellet” problem more clearly.

So, failure to catch fire in 36 minutes can usually happen due to a lot of ash being filled in the area under the pot where the ignitor resides. 

The 5 times blinking status light can lead your stove to either one of the three conditions:

  1. It can inhibit the airflow 
  2. It can hold back the igniter’s potential to get warmer enough 
  3. Lastly, the igniter itself can fail to catch fire.

The five-blink status light problem only occurs when you have an auto-ignited pellet stove. In this condition, the focus should be on the igniter, as you may need to change it. For this purpose, you first need to test your igniter, but the question is, how can you do that at home?

How To Test The Igniter Of Your Harman Pellet Stove?

Switch Off & on Your Igniter

The first and foremost thing you can do at home is to turn off your stove and switch it on once again from the selector switch on the control board and check if it is lit up.

Check On Your Stove Pellets

If switching off and on does not work, you can head toward checking whether your stove pellets are damp because wet or damp wood pellets take a lot of time to ignite and burn consistently. They also create more smoke and dust as they have reduced density. 

Note: Harman stove can burn any pellet, but sometimes it also depends on the pellet quality because a higher quality pellet means less effort to clean ash and cleanse the stove.

Check On To Pellet Quality

If you buy a higher quality pellet, the Harman stove needs less maintenance chaos as it will get the most out of that. The pellets are graded based on their ash contents in a system including:

Utility pellet: If you invest in these pellets, you will likely have to clean your stove after every four to five days.

Premium Pellet: These pellets are expensive, but they have a standard to catch flames below 0.5 percent as they are typically created from the sawdust waste produced from the timber production process.  

Super Premium Pellet: This grade has softwood pellets made with filler, bark, or binding agents that create a healthy fuel source for a more extended period, even with smoke. It also gives consistent temperature along with favorable results. Plus, you will have about two weeks to clean the ashes from the Harman stove after putting super-premium pallets into it. 

Matt Goense, the owner of Kring’s Hearth & Home in Bechtelsville, Pennsylvania, says, “There are different brands, and which one you like is all a matter of your own opinion. It’s like asking someone what coffee tastes better to them.”.

This means the peace of mind comes with knowing that you can burn any of the pellets mentioned above without worrying, as they can be cleansed easily from your Harman stove.

Check OHMS On Igniter

The fourth thing to find out the reason behind the 5 blinks of status light is to check the ohms on the igniter, which can be described as a unit of electrical resistance or a measurement of resistance between two points of a conductor.

The reading at the harman pellet stove should lie between a range of 45 to 53 ohms, and typically, it runs between 47 and 49. 

  • So, this can be checked through a multimeter and looking for this simple “Ω” on the screen of our multimeter. 
  • Set the cursor to the ohm symbol, which you can see on the top of your multimeter.
  • Unhooked or unplugged your igniter, and you will see two tabs at the end of it.
  • The multimeter has two pins. One is red, and the other is black
  • Simply put those pins on the tabs of the igniter and see if the range lies between 47 to 49.
  • The range will be shown on the screen of your multimeter. If it ranges between 47 to 49, it means it is good. But, if it is out of range, the status light will blink 5 times on the stove.

There are various ways to remove the Harman 5 blink error written below:

  • First, you can turn the mode selector OFF and then turn it ON again. In most cases, this technique will help.
  • If switching off & on does not help, then there might be no pellet left in the hopper or your igniter needs to be fixed in catching fire. For this purpose, add some high-quality pellets to your harman stove.
  • Thirdly, the auger motor in your harman stove may get old and tired. Therefore, it is time to clean the motor or t simply change it.
  • Lastly, you have to check whether ashes are left in the burn pot because the increased amount of ashes can get between the fins on the igniter. This condition does not allow the air to pass through the fins, making the pellet more challenging to catch fire. For this purpose, you need to clean the burn pot and the fins in the igniter as soon as possible to get a better result from your harman pellet stove.

Consumers’ Reviews

Consumers around the world are happy with the features and quality of the Harman pellet stove, as some of them commented that they love the traditional design and it is effortless to keep the maintenance of this stove.

They also love the reliability and efficient features of the harman stove as it can quickly fire up the chill & icy cold weather.

Furthermore, some consumers found the company’s customer service very friendly and great. 

Therefore, You can eliminate the traditional chimneys, cutting wood and burning them to make your winter cozier.

Now you can simply invest in a harman pellet auto stove to make your life easier and warmer in cold and icy weather.

Conclusion

The bottom line is if you ever found 5 blinking status lights on your harman pellet stove, then the first and foremost thing to do is to check the burn pot to see if any ashes are left.

Clean it in a good way for high-quality results. Furthermore, there can be a situation where your auger motor or harman is getting old, so you may need to change it.

Other possible reasons, along with solutions, are mentioned above. So, give it a good read to find the matter with your harman stove and solve it at home in the easiest way.